Apc Smart Ups 2200 Manual

13-05-2021

Apc Smart Ups 2200 Manual

APC; Smart-UPS 2200VA; User Manual; APC Smart-UPS 2200VA SUA2200I User Manual. Product codes. Download Like. Full screen Standard. Page of 16 Go. Smart-UPS 2200/3000 VA 100/120/230 Vac Tower User Manual. All LEDs are off and the UPS is plugged into a wall outlet. Read and download APC Battery Charger Smart UPS 2200 VA User's Manual online. Download free APC user manuals, owners manuals, instructions, warranties and installation guides, etc.

Size:Download

This UPS has a diagnostic feature that displays the utility voltage. With the UPS plugged into the normal utility power, press and hold the on/test button to see the utility voltage bar graph display. After approximately four seconds the 5-LED display on the right of the front panel shows the utility input voltage. Refer to the figure below for the voltage reading.

When loads exceed the UPS’s capacity, the overload LED illuminates, the UPS emits a sustained tone, and the input circuit breaker may trip (the resettable center plunger of the circuit breaker pops out). The alarm remains on until the overload is removed. Disconnect nonessential load equipment from the UPS to eliminate the overload. If there is AC power and the circuit breaker does not trip during overload, the loads are still powered. If the circuit breaker trips and the UPS attempts to go on-battery, the output AC will shut down.

When the UPS is off and there is no utility power, it is possible to cold start the UPS to power the loads from the UPS’s battery.

7 min.

Press the configuration button once to set the low battery warning interval to approximately five minutes. Press it again to set the interval to

approximately seven minutes. Press the button a third time to reset the interval to two minutes.

By default, the low battery warning occurs when there are approximately two minutes of on-battery run time remaining. This may not be enough time to gracefully shut down some protected computer systems.

To change the warning interval, press the rear panel configuration button while pressing and holding the front-panel

2 min.

Initial Start-Up

To obtain warranty coverage, please fill out and return the warranty registration card now.

Inspection

Inspect the UPS upon receipt. Notify the carrier and dealer if there is damage. The packaging is recyclable; save it for reuse or dispose of it properly.

Placement

Install the UPS in a protected area that is free of excessive dust and has adequate air flow. Do not operate the UPS where the temperature and humidity is outside the specified limits.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the warranty.

Installation

To install this UPS, please follow the installation instructions in the Smart-UPS Quick Reference Guide.

This UPS is equipped with a SmartSlot for accessories. See the APC Website (www.apcc.com) for available accessories.

Charge the battery

The UPS charges its battery whenever it is connected to utility power. The battery will charge fully during the first 4 hours of normal operation. Do not expect full runtime during this initial charge period.

Operating Instructions

Switch On — Switch Off

With the UPS plugged in, press and release the large upper on/test button to supply power to the loads. The

loads are immediately powered while the UPS performs a self-test.

Press and release the small, lower off button to turn off power to the loads. It may be convenient to use the UPS as a master on/off switch for the protected equipment.

Note: Whenever the UPS is plugged in and utility voltage is present, the charger maintains battery charge.

Theon-lineLED illuminates when the UPS is supplying utility power to the loads.

Self-test

The UPS performs a self-testautomatically when turned on, and every two weeks thereafter (by default). Automaticself-testeases maintenance requirements by eliminating the need for periodic manualself-tests.

During the self-test,the UPS briefly operates the loadson-battery.If the UPS passes theself-test,it returns toon-lineoperation.

If the UPS fails theself-testit immediately returns to online operation and lights the replace battery LED.

The loads are not affected by a failed test. Recharge the battery overnight and perform the self-testagain. If the replace battery LED is still on, replace the battery using theReplacing the Battery procedure.

SmartTrim

The SmartTrim LED comes on to indicate that the UPS is compensating for a high voltage.

SmartBoost

The SmartBoost LED comes on to indicate that the UPS is compensating for a low voltage.

APC Smart-UPS

Uninterruptible Power Supply

230 VAC User’s Manual

Rear Views

2200 and 3000 VA

1000 and 1400 VA

450 and 700 VA

Connect Computer Interface Port (Optional)

Power management software and interface kits can be used with this UPS. Use only kits supplied or approved by the manufacturer. If used, connect the interface cable to the 9-pincomputer interface port on the back panel of the UPS. Secure the connector’s screws to complete the connection.

Connect Ground Leads to TVSS Connector (Optional)

Apc Smart Ups 2200 Service Manual

The UPS features a TVSS connector for connecting the ground lead on transient voltage surge-suppression(TVSS) devices such as telephone and network line protectors. The TVSS connector provides grounding through the UPS’s power cord ground conductor. To make a connection to the TVSS connector, loosen the screw and connect the surge suppression device’s ground lead. Tighten the screw to secure the lead.

Battery Pack Connector (3000 VA only)

Use the battery pack connector to connect the optional external battery pack.

On Battery

During on-batteryoperation, theon-batteryLED illuminates and the UPS sounds an audible alarm consisting of four beeps every 30 seconds. The alarm stops when the UPS returns toon-lineoperation.

Low Battery

When the UPS is operating on-batteryand the energy reserve of the battery runs low, the UPS beeps continuously until the UPS shuts down from battery exhaustion or returns toon-lineoperation.

100%	Battery Charge Bar Graph
80%	The 5-LEDdisplay on the right of the front panel
60%	shows the present charge of the UPS’s battery as a
60%	percentage of the battery’s capacity. When all five
40%	percentage of the battery’s capacity. When all five
40%	LEDs light, the battery is fully charged. The top
20%	LED goes out whenever the battery is not 100%
charged. When the LEDs are flashing, the battery

can supply less than the “low battery warning interval” time for the load.

Shutdown Mode

If there is no utility power present, a host system connected to the computer interface port can command the UPS to shut down. This is normally done to preserve battery capacity after a controlled shutdown of the protected system. In shutdown mode the UPS stops supplying power to the load, waiting for the return of utility power.

The UPS scrolls the front panel indicators sequentially in shutdown mode. If the UPS has shutdown due to a low battery, the UPS lights the Battery Charge Bar Graph only. When line power is restored, the UPS returns to on-lineoperation.

Replace Battery

If the battery fails a self-test,the UPS emits short beeps for one minute and the replace battery LED illuminates. The UPS repeats the alarm every five hours. Perform theself-testprocedure to confirm replace battery conditions. The alarm stops when the battery passes theself-test.

85%	Load Bar Graph
67%	The 5-LEDdisplay on the left of the front panel
50%	shows the power drawn from the UPS by the load.
	The display indicates the percentage of the UPS’s
33%
	rated capacity. For example, if three LEDs are lit, the
17%
	load is drawing between 50% and 67% of the UPS’s
capacity. If all five LEDs light, thoroughly test your
complete system to make sure that the UPS will not
become overloaded.

990-7020C,Revision 7, 3/00

Voltage Sensitivity

The UPS detects line voltage distortions such as spikes, notches, dips, and swells, as well as distortions caused by operation with inexpensive fuel-poweredgenerators. By default, the UPS reacts to distortions by transferring toon-batteryoperation to protect the loads. Where power quality is poor, the UPS may frequently transfer toon-batteryoperation. If the loads can operate normally under such conditions, battery capacity and service life may be conserved by reducing the sensitivity of the UPS.

To reduce UPS sensitivity, press the configuration button on the rear panel. Use a pointed object such as a pen to press the button. Press it once to set the UPS’s sensitivity toreduced. Press it again to set the sensitivity tolow. Press the button a third time to

reset normal sensitivity.

normal

reduced	When the UPS is set to normal sensitivity, the
	configuration LED is brightly lit. When it is set to
low
	reduced sensitivity, the LED is dimly lit. When it is
set to low sensitivity, the LED is off.

•Press and hold the on/test button until the UPS begins beeping.

•Release the on/test button during the beeping to start the UPS.

Utility Voltage Bar Graph

196		If no LEDs come on and the UPS is plugged into a
		working AC power outlet, the line voltage is extremely
264
	low. If all five LEDs come on, the line voltage is
	extremely high and should be checked by an electrician.
	The display indicates that the voltage is between the
247	displayed value from the list and the next higher value.
230	For example, with three LEDs lit, the input voltage is
213	between 230 and 247 VAC.

Note: The UPS starts a self-testas part of this procedure. Theself-testdoes not affect the voltage display.

Storage

Storage Conditions

Store the UPS covered and upright in a cool, dry location, with its battery fully charged. Before storing, charge the UPS for at least 4 hours. Disconnect any cables connected to the computer interface port to avoid unnecessarily draining the battery.

Extended storage

•At -15to +30 °C (+5 to +86 °F), charge the UPS’s battery every 6 months.

•At +30 to +45 °C (+86 to +113 °F), charge the UPS’s battery every 3 months.

Importer's Name and Address:

Standards to Which Conformity Declared: Manufacturer's Name and Address:

89/336/EEC,73/23/EEC,92/31/EEC,

EN55022, EN50082-1, EN50091, EN60950 American Power Conversion

West Kingston, Rhode Island, 02892, USA -or-

American Power Conversion (A. P. C.) b. v. Ballybritt Business Park

American Power Conversion Phillipines Second Street

Roserio, Cavite Phillipines

American Power Conversion (A. P. C.) b. v. Ballybritt Business Park

Smart-UPS 450, 700, 1000, 1400, 2200, 3000 X9601 000 0000 — X9699 999 9999* X9701 000 0000 — X9799 999 9999*

Years of Manufacture: 1995, 1996, 1997, 1998, 1999, 2000 Note: Where X = B, O, W, or D

We, the undersigned, hereby declare that the equipment specified above conforms to the above directives. Billerica, MA 1/1/97

Apc Smart Ups Rt 2200 Manual Pdf

Type of Equipment: Model Numbers: Serial Numbers:

Replacing the Battery

This UPS has an easy to replace hot-swappablebattery. Battery replacement is a safe procedure, isolated from electrical hazards. You may leave the UPS and loads on for the following procedure. See your dealer or call the number in this manual for information on replacement battery kits.

Note: Please read the cautions in the APC Safety Guide.

Once the battery is disconnected, the loads are not protected from power outages.

Battery Replacement Procedure - 2200 - 3000 VA Models

1. Grasp the top edge of the bottom front cover and tilt it out.

2.Unhook the bottom section of the front cover from the chassis and set it aside.

3.Use a flat-bladescrewdriver or a coin to remove the two battery door screws and

open the door.

4. Grip the wires for the front set of batteries and pull firmly to disconnect the connector from the battery compartment. Remove the batteries.

5.Pull the white cord on the front battery connector to remove the batteries.

6.Set aside the foam spacer located between the batteries.

7.Reach into the battery compartment and grasp the white cord on the other battery connector. Pull firmly to disconnect the connector and remove the second set of

batteries.

Note: Be careful removing the batteries - they are heavy.

8.Slide the first set of new batteries into the unit. Hold the connector down below the top of the batteries and toward the door, otherwise the assembly will not fit. Guide the connector over the top of the batteries and press firmly to connect it to the rear connector of the battery compartment.

9.Set the foam spacer against the rear batteries to prevent the wires from being pinched.

Note: Small sparks at the battery connectors are normal during connection.

10.Slide the second set of batteries in, then guide the connector over the batteries and press firmly to connect it to the front connector of the battery compartment.

11.Now close the battery door, replace the screws, and replace the lower front cover.

12.Dispose of the old battery properly at an appropriate recycling facility or return it to the supplier in the packing material for the new battery. See the new battery instructions for more information.

Battery Replacement Procedure - 450 - 1400 VA Models

1. Grasp the top of the front cover and tilt it out and down.

2.Unhook the bottom of the cover from the chassis and lift it upward to expose the battery door. Be careful not to strain the ribbon cable. Do not touch the exposed

printed circuit board.

3. Fold the front cover on top of the UPS as shown.

4. Use a flat-bladescrewdriver or a coin toremove the two battery door screws and open the door.

Grasp the tab and gently pull the battery out of the UPS. 5. Disconnect the battery leads.

•For the 450 through 1000 VA models, loosen the connectors by gently wiggling them while pulling straight back from the battery connector.

• For the 1400 VA model, pull the two gray couplers apart to disconnect the battery.

6. Connect the battery leads to the new battery.

1400 VA	Note: Small sparks at the battery connectors are normal during connection.
• For the 450 through 1000 VA models, connect the red wire to the positive (+)
terminal and the black wire to the negative (–)terminal.
450 - 1000 VA	• For the 1400 VA model, connect the gray battery coupler to the UPS’s coupler.
7. Now slide the battery into the UPS,close the battery door,replace the battery

compartment screws, and replace the front cover.

8. Dispose of the old battery properly at an appropriate recycling facility or return it to the supplier in the packing material for the new battery. See the new battery instructions for more information.

Place	Date	Stephen A. Lee, Regulatory Compliance Engineer
Galway, Ireland	1/1/97
Place	Date
		Gerard	Rutten, Managing Director, Europe

User Configuration Items

Note: Setting these items requires optional software or hardware.

Function	Factory	User Selectable Choices	Description
Default
Automatic Self-Test	Every 14 days	Every 7 days (168 hours),	Sets the interval at which the UPS
(336 hours)	On Startup Only, No Self-	will execute a self-test.
Test
UPS ID	UPS_IDEN	Up to eight characters to	Use this field to uniquely identify the
define the UPS.	UPS for network management
purposes.
Date of Last Battery	Manufacture	Date of Battery	Reset this date on battery
Replacement	Date	Replacement	replacement.
Minimum Capacity Before	0 percent	15, 50, 90 percent	The UPS will charge its batteries to
Return from Shutdown	the specified percentage before return
from a shutdown.
Sensitivity	Normal	Reduced, Low	Set lower than normal sensitivity to
avoid lowered battery capacity and
service life in situations where the
load can tolerate minor power
disturbances.
Duration of Low Battery	2 minutes	5, 7, 10 minutes	Sets the time before shutdown at
Warning	which the UPS issues a low battery
warning. Set higher than the default
only if the OS needs the time for
graceful shutdown.
Alarm Delay After Line Fail	5 second delay	30 second delay, At Low	To avoid alarms for minor power
Battery Condition, No	glitches, set the alarm delay.
Alarm
Shutdown Delay	20 seconds	180, 300, 600 seconds	Sets the interval between when the
UPS receives a shutdown command
and when shutdown occurs.
Synchronized Turn-onDelay	0 seconds	60, 180, 300 seconds	To avoid branch circuit overload,
the UPS will wait the specified time
after the return of utility power before
turn-on.
Output Voltage	230 Vac	220, 225, 240 VAC	Sets the output voltage for on-battery
operation.
High Transfer Point	253 Vac	264, 271, 280 VAC	To avoid unnecessary battery usage,
set the High Transfer Point higher if
the utility voltage is chronically high
and the load is known to work well
under this condition.
Low Transfer Point	196 Vac	188, 204, 208 VAC	Set the Low Transfer Point lower if
the utility voltage is chronically low
and the load can tolerate this
condition.

Service

If the UPS requires service do not return it to the dealer!

Follow these steps:

1.Use the Troubleshooting section of theQuick Reference Guide to eliminate common problems.

2.Verify that no circuit breakers are tripped. A tripped circuit breaker is the most common UPS problem!

3.If the problem persists, call customer service or visit the APC Internet Website (www.apcc.com).

•Note the model number of the UPS, the serial number, and the date purchased. A technician will ask you to describe the problem and try to solve it over the phone, if possible. If this is not possible the technician will issue a Return Merchandise Authorization Number (RMA#).

•If the UPS is under warranty, repairs are free. If not, there is a repair charge.

4.Pack the UPS in its original packaging. If the original packing is not available, ask customer service about obtaining a new set.

•Pack the UPS properly to avoid damage in transit. Never use Styrofoam beads for packaging. Damage sustained in transit is not covered under warranty.

•Include a letter with your name, RMA#, address, copy of the sales receipt, description of the trouble, your daytime phone number, and a check (if necessary).

5.Mark the RMA# on the outside of the package

6.Return the UPS by insured, prepaid carrier to the address given to you by Customer Service.

North & Latin America	Europe
APC	APC
132 Fairgrounds Road	Ballybritt Business Park
West Kingston, Rhode Island 02892 USA	Galway, Ireland 10800-702000
1-800-800-4APC/1-401-789-5735	353-91-702020
Internet: http://www.apcc.com
E-Mail:apctech@apcc.com	E-Mail:apceurtech@apcc.com

Apc Smart Ups 1500 User's Manual

Regulatory Agency Approvals

N 3 9 M E6 1

Apc Smart Ups 2200 Lcd Manual

Specifications